Checking steering swivel pins

Tools you might need

Wishbone suspension- paul-ryan.info Top swivel pin Steering swivelmember Bottom swivelpin

Wishbone suspension

Steering swivel pins may wear out after a high mileage (60,000 ), or sooner if they have not been properly lubricated. A badly worn joint is dangerous - not only does it make the steering wander, but it may suddenly fail altogether.

Worn joints need special equipment to replace and the work should be done by a garage, but you can check them yourself. You need a helper and a long flat, steel bar such as a large tyre lever.

Make sure the car is on level ground, put the handbrake on firmly, and the car in first gear if it is a rearwheel-drive model. Put a car with automatic transmission in 'P' or 'park'. Chock both rear wheels, then jack up the car to raise one front wheel, and put an axle stand under a chassis member, so that the other front wheel remains firmly on the ground.

Never work under a car when it is supported only by a jack. Always use axle stands placed under a strong chassis member.

First inspect any rubber dust seals or covers on the swivels for signs of perishing, cracks or splits. If you find any, almost certainly dirt or grit will have entered the joints, they will be damaged and they must be replaced.

Some cars have rubber or nylon bushes inside various joints in the top, bottom or both swivel pins. So far as these are visible, check them for perishing, cracking or softening caused by oil.

If they are not visible, excessive wear or damage will show up anyway in the routine test. Here, too, any damage calls for replacement.

A MacPherson-strut suspension has its top swivel bearing inside the strut. Inspect it when you check strut mountings (See Checking suspension joints and pivots). The bottom bearing can be checked, however.

How to check wishbone suspension

Wishbone suspension- paul-ryan.info Top swivel pin Steering swivelmember Bottom swivelpin

Wishbone suspension

Place yourself where you can see clearly the top and bottom swivel pins and the steering swivel member that joins them on the suspension that has been raised. Ask your helper to grasp the wheel firmly at top and bottom, and rock it by pushing with alternate hands use a fair amount of force. The wheel should move a little, because of free play at the hub bearing (See Adjusting wheel bearings).

This play makes the brake disc or drum move relative to its backplate, and is easy to see. Watch the top and bottom swivels and steering swivel member. If the joints are worn, you can see the swivel member move in and out in relation to the top or bottom suspension arms.

- paul-ryan.info Look forin-and-outmovementhere

Watch the joints while a helper rocks the wheel.

- paul-ryan.info Look forverticalmovementhere

Levering the tyre up and down.

To test for vertical play, put a screw or hydraulic jack under the lower suspension arm, and raise it until the suspension is compressed.

Again, watch from where you can see both top and bottom joints. Get your helper to put a strong lever or bar under the tyre and move it up and down while you watch for movement at either joint.

Some ball joints have spring-loaded pins which allow a small amount of vertical play, generally no more than in. (1.5 mm). Anything greater means a worn joint.

If the maximum permissible play is not in the car handbook, consult your nearest agency. If the pins are not spring-loaded, any visible play means that they are worn and must be replaced.

Checking a MacPherson strut

- paul-ryan.info Strut The lowersuspensionarm has aball-jointswivel

The upper swivel is at the top inside the wing, and is not visible.

Only the lower swivel joint can be checked for play. With the front of the car raised so that the wheel hangs free, ask your helper to hold the wheel back and front and rock it from side to side.

If the joint moves at all, vertically or horizontally, it is defective and must be replaced. The steering may deflect a little during this test; take care not to confuse this with play at the joint.

Check for vertical movement also by resting a lever against the inner wheel rim and pushing upwards against the joint.

MacPherson-strut front suspension can be found on both front-wheel and rear-wheel-drive cars. Here it is on a front-wheel drive.

- paul-ryan.info Look formovementhere

Helper rocks the wheel from side-to-side.

- paul-ryan.info Look formovementhere

Lever the lower arm against the wheel rim while watching the joint.

We also have this article in

The ultimate video course

We take this car to pieces and then build it again, explaining how every single part works.

By the time you finish watching this, you'll understand everything inside a car.

Watch us take a Mazda MX5 Miata to pieces, and then build it back together again into a modern working car.

  • 3+ hours of HD video available now. Production complete by July 2018.
  • Every part explained in detail.
  • We've created the most detailed 3D model ever produced so we can show you everything working.
  • Over 20 hours of footage — see the contents.
  • Buy now and get our 150 page PDF for free.

This is the most in-depth course on car mechanics ever produced. Buy now and save 75%.

Buy today for $20
Normal price $80.

Read more essential guides

Checking steering joints for wear

The joints in a steering system all wear gradually and become slack. Because there are so many o...

Refitting track rods and ball joints

Check that any parts you are not going to replace are undamaged before ordering replacements. Re...

Checking steering-rack security

Most modern cars have rack-and-pinion steering gear, mounted across the car. Usually the rack ho...

Checking rack and pinion steering

Part of a steering rack check involves raising the front of the car but retaining its weight on ...

How to lubricate the steering system

Most modern cars have sealed for life joints in at least part of the steering system. These do no...


читать дальше

шкаф купе заказать киев