×

Adjusting a fixed-jet carburettor

Tools you might need

A fixed-jet carburettor mixes air and fuel by means of several jets. The jets are small holes which allow precisely controlled amounts of fuel or air to flow through them. The amounts are governed by the diameter, length and shape of the jets.

Typical fixed-jet carburettor- paul-ryan.info Choke disc; thethrottle disc orbutterfly islower down. Choke linkage Throttle-stop screwrestricting the travelof the lever. Throttle lever, connectedto a throttle rod. Volume-control screw:this one regulates fuelflow. Fuel pipe The acceleratorpump delivers alitle extra fuel foracceleration.

Typical fixed-jet carburettor

The jets in this type of carburettor are not adjustable, so the air-fuel mixture is adjusted by directly regulating the flow of fuel or air into them.

The jets come into action as needed by changes in the vacuum inside the carburettor, caused by different engine speeds and throttle openings.

Since the jets are fixed - not adjustable - the mixture is adjusted by directly regulating the fuel or air flow to them.

On carburettors made before about 1974 you can adjust two settings. One is the volume of fuel (or on some types, air) going into the engine. The other is the engine's idling speed, which is set by adjusting the throttle-stop screw.

The adjustment screws are located differently on different carburettors.

Later carburettors have had to comply with anti-pollution laws concerning exhaust gases.

They are called emission-control carburettors, and have sealed, tamperproof adjustments which generally you cannot change (See Adjusting an emission-control carburettor).

Air cleaner stays on- paul-ryan.info

Air cleaner stays on

If possible, make adjustments without removing the air cleaner.

Before you tune the carburettor, make sure that it needs tuning, by eliminating all other causes of bad running (consult Faultfinder).

Certain adjustments are made with the engine running, so while it is cold, find the adjustment screws and work out how to reach them easily without burning yourself when working with the engine hot.

It may also help you to do the job without removing the air cleaner. Removing the air cleaner increases air flow and upsets the mixture.

Bring the engine up to normal working temperature, then work quickly before it gets much hotter - which would also affect the mixture.

Adjustment

- paul-ryan.info

The volume-control screw may be knurled so that you can turn it by hand.

Set the throttle-stop screw so that the engine idles a little faster than normal.

Turn the volume-control screw either way, until the engine begins to run roughly.

- paul-ryan.info

The throttle-stop screw increases engine speed when turned clockwise.

On most carburettors the volume screw regulates fuel flow — on this type the volume screw's position is low on the carburettor body.

Turning it clockwise weakens the mixture, causing 'hunting' — a rhythmical rise and fall in engine speed.

Turning it anti-clockwise enriches the mixture, producing 'lumpy', irregular running.

An air volume-control screw is placed higher up. Turning it clockwise enriches the mixture; turning it anti-clockwise weakens the mixture.

Find the two points at which hunting and lumpy running begin. Set the screw halfway between them, unless some other setting clearly makes the engine run better. Note the screw setting.

Reset the throttle-stop screw for a normal idling speed, and repeat the test with the mixture screw. Probably this will result in the same final setting.

Adjusting Weber and Solex carburettors

Adjusting a Weber carburettor- paul-ryan.info Throttle-stopscrew Mixture adjusting screw

Adjusting a Weber carburettor

On a Weber, the mixture-adjusting screw is sealed in many later types. Idling speed is adjusted by turning the throttle-stop screw.

Adjusting a Solex carburettor- paul-ryan.info Throttle-stopscrew Bypassidle-speedscrew

Adjusting a Solex carburettor

On a Solex, idling speed is adjusted by turning the bypass idle-speed screw, which is sealed by a plastic cap on later models.

We also have this article in

The ultimate video course

We take this car to pieces and then build it again, explaining how every single part works.

By the time you finish watching this, you'll understand everything inside a car.

Watch us take a Mazda MX5 Miata to pieces, and then build it back together again into a modern working car.

  • 3+ hours of HD video available now. Production complete by July 2018.
  • Every part explained in detail.
  • We've created the most detailed 3D model ever produced so we can show you everything working.
  • Over 20 hours of footage — see the contents.
  • Buy now and get our 150 page PDF for free.

This is the most in-depth course on car mechanics ever produced. Buy now and save 75%.

Buy today for $20
Normal price $80.

Read more essential guides

Adjusting an emission-control carburettor

Anti-pollution laws in many countries now limit the volume of poisonous carbon monoxide gas (CO)...

How the fuel system works - fixed-jet carburettors

The fixed-jet carburettor resembles the simpler variable-jet type (See How variable-jet carburet...

Preparing for carburettor adjustment

The carburettor is often suspected of causing an engine to run roughly, when the real source of t...

Checking and cleaning an SU carburettor

The SU carburettor is simple to strip. It has only one jet (except in a few special types) and...

Checking and cleaning a fixed-jet carburettor

Fixed-jet carburettors are easily blocked by small dirt particles and chemical residues from fue...

источник

читать далее

ссылка