×

How engine timing works

Distributor- paul-ryan.info Cam lobes Baseplate Vacuum chamber Centrifugal weights Distributor shaft

Distributor

The distributor both sends the HT current to the correct sparkplug and ensures that it arrives at the best time for maximum efficiency.

For an engine to work at its best, the fuel/air mixture in each cylinder must fire just as the piston reaches top dead centre (TDC).

It takes a certain time for the spark-plug to ignite the mixture and for the combustion to build up. This time stays roughly the same no matter how fast the engine is running.

The timing mechanism is set to fire the plug a short time before the TDC. But because the mechanism is worked by the motion of the engine, this time would normally decrease as the engine ran faster, and the plug would fire too late.

So a mechanical device is fitted to advance firing - make it happen earlier - with increasing engine speed.

The load on an engine - whether it is pulling hard or cruising - also affects the timing.

A lightly loaded engine works best if the ignition is advanced an extra amount. A second vacuum-operated device controls this independently of the first.

Centrifugal advance mechanism

How the centrifugal weights work- paul-ryan.info Slow The centrifugalweights are in by thesprings at low enginespeed. Fast The centrifugalweights move outwardsagainst the springtension, advancing theignition.

How the centrifugal weights work

The centrifugal advance mechanism responds to engine speed. It is usually in the bottom of the distributor body under the -breaker baseplate.

Two steel weights are attached to a revolving plate on the distributor shaft by pivots, and held in the closed position by strong springs.

As the engine speeds up, centrifugal force throws the weights outwards.

They turn on their pivots, twisting the -breaker cam forwards so that the points open earlier, and the sparkplug fires earlier as the speed increases.

Vacuum advance mechanism

Two types of triggering mechanism- paul-ryan.info Triggerhead Timing rotor In this electronic system, steel ridges on a rotorcreate a small voltage as they pass through themagnetic field of the triggerhead. Magnetic strips embedded in the rotor create thevoltage in this system each time they are opposite thetriggerhead, which triggers a power transistor.

Two types of triggering mechanism

The vacuum advance mechanism responds to the vacuum in the engine inlet manifold, which is caused by the suction of the moving pistons. When the engine is lightly loaded the vacuum increases.

A narrow pipe runs from the manifold to a vacuum chamber on the distributor, inside which there is a flexible diaphragm.

As the vacuum increases, the diaphragm bends, moving a rod connected to its centre which causes the -breaker baseplate to swivel slightly. This moves the -breaker heel relative to the distributor cam and advances the ignition.

When the engine is under load, vacuum decreases, the diaphragm springs back and the ignition is retarded to suit the changed conditions.

Adjusting the timing

The usual way of adjusting the timing is to slacken the clamping bolt of the distributor and turn the whole unit slightly.

The amount by which the two advance mechanisms change the timing is not adjustable.

Some earlier distributors have a knurled nut on the vacuum advance mechanism, by which you can alter the timing as a whole (not just the action of the mechanism).

How electronic ignition works

Many newer cars have an electronic ignition system which times the spark more precisely than a mechanical system.

It also wears less, so that it is always at peak efficiency, and it overcomes one problem of a mechanical system: at high engine speeds a mechanical system does not work at peak efficiency.

Electronic systems may be of the inductive discharge or capacitive discharge type.

An inductive discharge system is the type usually fitted as original equipment on cars with electronic ignition. It produces high-tension (HT) current in the normal way: by switching low-tension (LT) current off and on in a coil.

In the simplest inductive discharge system, the transistor-assisted s (TAC) type, there is also a normal breaker.

It carries only a very small current, which is fed to a power transistor which switches on and off the heavier LT current to the coil.

The -breaker points are not eroded by the small current, so they stay clean for longer, and the gap seldom needs resetting.

More advanced, fully electronic systems may not have points. Instead, the distributor contains another form of triggering device for the power transistor which relies on electrical pulses instead of a mechanical make-and-break method.

In one type there is an electromagnetic coil and a revolving spiked rotor with one steel spike for each cylinder.

Every time a spike moves past the coil it creates a small voltage which triggers the transistor.

Some other types may have optical or magnetic triggers - they all perform the same function.

A capacitive discharge (CD) system - used in some do-it-yourself kits produces HT current in the coil by sending a large pulse from a capacitor through the primary winding.

The capacitor is an electrical storage device which can be charged and discharged very rapidly.

The secondary windings of the coil produce HT current both at the moment when the LT current in the primary windings is switched on, and at the moment it is switched off.

Because a capacitor can give a very large pulse very fast, there is always a strong spark, irrespective of the speed of the engine.

The timing in this system may again be fully electronic or it may use the -breaker points.

We also have this article in Spanish and French

The ultimate video course

We take this car to pieces and then build it again, explaining how every single part works.

By the time you finish watching this, you'll understand everything inside a car.

Watch us take a Mazda MX5 Miata to pieces, and then build it back together again into a modern working car.

  • 3+ hours of HD video available now. Production complete by July 2018.
  • Every part explained in detail.
  • We've created the most detailed 3D model ever produced so we can show you everything working.
  • Over 20 hours of footage — see the contents.
  • Buy now and get our 150 page PDF for free.

This is the most in-depth course on car mechanics ever produced. Buy now and save 75%.

Buy today for $20
Normal price $80.

Read more essential guides

How the steering system works

The steering system converts the rotation of the steering wheel into a swivelling movement of th...

Checking the high-tension circuit

The high-tension (HT) or secondary circuit carries high-voltage electricity. It runs from the se...

Checking for oil leaks

If an engine needs topping up with fresh oil more than usual, or if you see a pool of oil...

Overhauling a Bosch distributor

Bosch distributors are found on many different cars and are generally very reliable. But after a...

Stroboscopic timing

A static timing check with the engine stationary is never fully accurate. It does not allow for ...

link

link

別れさせ屋 千葉